• Can the ALL-TEST Pro™ Electrical Signature Analysis test motors greater than 600 Volts?
• Can the ALL-TEST PRO™ On-Line series test DC Motors?
• Can the ALL-TEST PRO™ On-Line series test Generators?
• Can the ALL-TEST PRO™ On-Line series test Variable Frequency Drive applications?
• How long does it take to apply ALL-TEST Pro™ Motor Circuit Analysis and Electrical Signature Analysis technologies?
• How do I setup the Bluetooth® adpter for my ALL-TEST PRO On-Line II (ATPOL II)?
• My ATPOL II will not communicate with my computer even though they are paired
• I keep getting an "Access Violation" everytime I run the Electrical Signature Analysis software, how do I get rid of this message?
• I installed the Electrical Signature Analysis Software and got the following message, "A/D card driver CBW32.DLL is NOT installed"
Back to Top
• Can the ALL-TEST PRO™ On-Line series test motors greater than 600 Volts?
Yes. However, the standard test fixtures are rated for 600 Volts, so you have to use the motor’s CT’s and PT’s when testing above 600 Volts. Special order test fixtures are available for high voltage applications.
Back to Top
• Can the ALL-TEST PRO™ On-Line series test DC Motors?
Absolutely. ALL-TEST Pro™ has extensive experience testing DC motors both energized and de-energized. The ALL-TEST PRO™ OL even allows the technician to troubleshoot the DC Drive’s operation. All can be done with one less than 1 minute reading.
Back to Top
• Can the ALL-TEST PRO™ On-Line series test Generators?
Both AC (Alternators) and DC (Generators) can be tested with the ALL-TEST PRO™ On-Line series. The ALL-TEST PRO On-Line Series is one of the only instruments on the market that can test a generator online.
Back to Top
• Can the ALL-TEST PRO On-Line series test Variable Frequency Drive applications?
Absolutely. ALL-TEST Pro has extensive experience testing both the motor and VFD in variable frequency drive applications. Just as with DC applications, the ALL-TEST PRO OL even allows the technician to troubleshoot the VFD’s operation. All of this is done with a simple 1 minute reading.
Back to Top
• How long does it take to apply ALL-TEST Pro Motor Circuit Analysis and Electrical Signature Analysis technologies?
All of the ALL-TEST Pro™ instruments provide step-by-step menus for the operator along with simple data interpretation rules.
The ALL-TEST Pro™ software for both MCA and ESA technologies provide automated analysis of the electric motor and related systems. In effect, most ALL-TEST Pro™ technologies are put into use with only a few hours of self training. Expanded capabilities comes with experience, technical support and our onsite or off site training programs. The ALL-TEST IV PRO 2000 takes about 3 minutes for the testing while the ALL-TEST PRO On-Line Series takes about 1 minute.
Back to Top
• How do I setup the Bluetooth® adpter for my ALL-TEST PRO On-Line II (ATPOL II)?
1. Install the Bluetooth software from the ESA 4 CD.
NOTE: The Bluetooth adapter should NOT be inserted into the machine at this time and you will need to have administration rights to your computer.
2. After the Software installation is complete insert the Bluetooth adapter into an available USB port and wait for the computer to install the necessary drivers for the Bluetooth adapter.
3. Once the adapter has been initialized the Bluetooth symbol in the system tray (next to the time) will turn from white to blue
4. Turn on the ATPOL II instrument
5. Double click on the Bluetooth symbol in the System Tray. This will bring up a window that says IVT Corporation BlueSoleil – Main Window.
6. Press the orange ball in the middle of the window. This will find all active Bluetooth devices. Once the software is done detecting all devices, a white Bluetooth symbol will appear with Hexadecimal that will look something like 00:0C:84:00:28:C8,
(Note: Hexadecimal can use numbers 0-9 and the letters A–F or a–f.)
7. Double click on the new found device and connect to it. This will prompt you for a pass key. Enter the pass key at this time. Please note that you have 30 seconds to connect here or you will have to redo this step over again.
8. Right click on the device and click “CONNECT” and then “Bluetooth Serial Port Service.” A small window should appear stating that there is a serial connection and the serial port assignment. Make a note of the serial port assignment; you will need this for the Power System Manager. The Bluetooth symbol in the system tray will turn from blue to green.
9. If you missed the serial connection assignment you can right click on the Bluetooth connection and select “Status”
10. Once the connection has been made a green line will appear from the device to the orange ball in the middle with a little orange ball will travel from the device to the orange ball in the middle.
11. Now you may start the Power System Manager (PSM) software.
Back to Top
• My ATPOL II will not communicate with my computer even though they are paired
The ATPOL II communicates at 57600 baud rate. Verify that the communcation port (comm port) option in Power System Manager is set to 57600 and the correct comm port is selected.
Back to Top
• I keep getting an "Access Violation" everytime I run the Electrical Signature Analysis software, how do I get rid of this message?
The following access code violation appears upon startup of the Electrical Signautre Analysis (ESA) software. Clicking on OK allows proper operation of the ESA software.
To remove this warning from coming back
1. Close the running Electrical Signature Analysis software that is presently running
2. remove 2 files from the folder where the software is stored and remove the following files:
emp.ini
setupemp
3. Restart ATPOL the message will have cleared
Back to Top
• I installed the Electrical Signature Analysis Software and got the following message, "A/D card driver CBW32.DLL is NOT installed"
Press "OK" on the Error message, to remove the error message.
By pressing the "OK" button the error message will not return, and the Electrical Signature Analysis software will operate correctly. |
